close

CM 630 Lightweight

CM 630 Lightweight is a dust reduced flooring product based upon cement and EPS.

The product is intended as a lightweight build-up on wood or any firm sublayer that are intended to be leveled with Combimix self-leveling underlayments.

Senden Sie alle Dateien

Alle Dateien herunterladen

info

Produktspezifikation

Technische Daten
add_circle
remove_circle

Druckfestigkeitsklasse

3.0 MPa without coating, 5.0 MPa with coating

Feuerwiderstandsklasse

Bfl-s1

Wärmeleitung/Konduction

0,1322 W / (mK)

Dicke 1

30–500 mm

Materialverbrauch

1 bag = approx. 46 litres (mixed with water)

Gewicht (trocken)

350 kg/m³

Wasserbedarf

7,5–9,5 l/50 liter

Betriebstemperatur

10–25 °C

Arbeitszeit

approx. 1 hr

Abbindezeit

20–30 hrs

Wasserschaden resistent

yes

Expansion nach dem Pumpen

< 15 %

Verpackung
add_circle
remove_circle

63010

50 l

info

Benutzen

Vorbehandlung
add_circle
remove_circle

The substrate should be clean and free of dust, cement skin, grease and other impurities that may prevent adhesion. In terms of the primer PP 600 forming a film, the temperature of the substrate must not fall below 10 °C. For best results, the ambient temperature in the work area should be between 10 and 25 °C. At higher or lower temperatures, the time for curing will shorten or extend. If it is ment as a floating floor, the subfloor shall be covered with age-resisting plastic before applying the CM 630. The plastic must be covering all horizontal and vertical surfaces.

Vermischung
add_circle
remove_circle

CM 630 is mixed with 7,5 - 9,5 liter of water for every 50 liter bag. CM 630 may be pumped with a special pump.

Anwendung
add_circle
remove_circle

CM 630 is applied evenly on the substrate and a straight-edge is used to get the right thickness. Use a Bull-float to get a good surface. The CM 630 is workable for about one hour. When pumped, the CM 630 might swell up to 15 % in volume afterwards.

Nachbehandlung und Härten
add_circle
remove_circle

The newly casted surface may be protected against too rapid dehydration by being covered with plastic, avoiding high temperatures, wind or direct sunlight. CM 630 is ready to be coated with self-leveling after 20–30 hours after casting, depending on temperature and RH. Coating with self leveling: CM 760: Min. 10 mm and no steelnet reinforcement necessary other than in wetrooms. Rest of the 700 series: Min. 20 mm and steelnet reinforcement.

Verbrauchsrechner

CM 630 Lightweight

Verbrauchsrechner

phone

+46 171 46 65 90

Kontaktieren Sie unsere Auftragsabteilung

Kontaktiere uns

  • Verkstadsvägen 6
  • 746 40 Bålsta, Schweden
  • Tel. +46 171 46 65 90
  • E-mail: [email protected]

Combimix

Combimix entwickelt und produziert Mineral-basierte Produkte für die Bauindustrie. Unsere Produktpalette umfasst Produkte für den Bodenausgleich, Fassadenputz, Rendering, Beton-Resurfacing und Restaurierungsmörtel für Kulturbauten. Wir führen Vertrieb in Schweden, Dänemark, Norwegen und den Vereinigten Staaten.

Produktkategorien