search
close

CM 8650 Light

CM 8650 Light is primarily intended to be used where a quick-drying, lightweight alternative is needed.

For use in homes, offices, public buildings and similar areas. CM 8650 Light is approved for use in marine environments. Suitable for stable substrates of concrete, ceramics, stone, steel, sheet metal or wood, where there is little risk of movement or deformation. Proper application thickness is 25-125 mm. Do not use product with underfloor heating due to its insulating properties. Minimum of 5 mm floor mortor is needed as underlay for carpeting. Reinforcement is needed for use on wood.

Send all files

Download all files

info

Product specification

Technical data
add_circle
remove_circle

Release of corrsive substances

CT (as per Marine directive 96/98/EC)

Compressive strength class

C5 (as per Marine directive 96/98/EC)

Compressive strength average

10 MPa (as per Marine directive 96/98/EC)

Flexural strength class

F2 (as per Marine directive 96/98/EC)

Flexural strength average

2,5 MPa (as per Marine directive 96/98/EC)

Fire resistance class

IMO FTPC Part 6 (lMO Res. A.687(17)),IMO FTPC Part2 (as per Marine directive 96/98/EC)

Adhesion to surface

> 0,6 MPa (as per Marine directive 96/98/EC)

Thickness 1

25–125 mm

Grain size

< 0.5 mm

Material consumption

0.65 kg/m²/mm

Weight (dry state)

650 kg/m³

Water requirements

3,2 l/12,5 kg

Workplace temperature

10–25 °C

Mixing time

3 min

Working time

25 min

Final set

1.5–2 hrs

Coverable (tiles)

3–6 hrs

Carpetable

8–16 hrs

pH

approx. 11

Water damage resistant

yes

Surface Tensile Bond Strength, 28 days (sanded, loaded surface)

> 1 MPa

Shrinkage

0.05 %

TVOC 28 days

> 10 μg/(m² h)

Packaging
add_circle
remove_circle

86501

12,5 kg

info

Use

Pre-treatment
add_circle
remove_circle

The substrate should be clean and free of dust, cement skin, grease and other impurities that can prevent adhesion. Adhesion and surface resistance of the substrate should be no less than 0.5 MPa. Always prime the substrate with PP 600 and apply wet-in-wet. In terms of the primer forming a film, the temperature of the substrate must not fall below 10°C. For best results, the ambient temperature in the work area should be between 10 and 25°C. In terms of the formation of cracks due to shrinkage or potential settling, do not cover a concrete structure earlier than one month after pouring the concrete.The guiding value of 90% RH during construction should be set as an upper limit during the application of the product.

Mixing
add_circle
remove_circle

CM 8650 Light is mixed with a max. 3.2 liters of water per 12.5 kg bag. Mix with a drilling machine with a whisk, and whisk until it becomes a stiff, lump-free compound that can be shaped into a ball in your hand. If the screed has started to dry out, do not try to mix in more water, rather discard the screed.

Application
add_circle
remove_circle

Spread the blended compound on the floor and compress and swipe with the straight edge of a lath to a thickness of min 25 mm. In wet rooms with an slope, set a lath along the wall and pull the mortar toward the floor drain. Always properly seal the drains to avoid clogging the drainage lines.

Post-treatment and curing
add_circle
remove_circle

The screeded, compressed surface can be floated immediately. Before the screed has managed to fully cure, smooth the surface with a trowel. Do not allow the material to dry too quickly and protect it from evaporation, high temperatures, drafts, etc. by placing a plastic cover over it. Final finish can be done as soon as the surface has dried. Always make sure that the material is sufficiently dry before treating with a wet room membrane. On dry substrates, the curing time in order to apply the wet room membrane is 8-16 hours after leveling with CM 8650 Light. The drying time specified assumes a curing environment with approximately 20°C, 40% RH and proper air flow. The curing time for laying carpet depends on what type of top spackling is used.

Consumption calculator

CM 8650 Light

Consumption calculator

phone

+46 171 46 65 90

Call our order department

Contact us

  • Verkstadsvägen 6
  • 746 40 Bålsta, Sweden
  • Tel. +46 171 46 65 90
  • Fax. +46 171 46 65 99
  • E-mail: info@combimix.com

Combimix

Combimix develops and manufactures mineral-based products for the construction industry. Our product range includes products for floor levelling, façade plastering, rendering, concrete resurfacing and restoration mortar for cultural buildings. We conduct sales in Europe and USA.

Product categories